Shenzhen Wisdomlong Technology CO.,LTD
Shenzhen Wisdomlong Technology CO.,LTD Work hard and best service for you!
Add to Cart
Redundant Power Supply Module SCHNEIDER TSX QUANTUM 140 CRP 932 00
OTHER SUPERIOR PRODUCTS
| Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
| Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
| Honeywell TC-,TK- | GE Modules IC - |
| Fanuc motor A0- | Yokogawa transmitter EJA- |
Open the Parameter Configuration
This table shows the steps required to open the parameter configuration
1 Call the Bus Editor
2 Select the module
3 Click on the right mouse button
Result: A shortcut menu is opened
4 Select Open Module
Result: The module opens with the parameter configuration window
Introduction
The numbering of channels of an I/O module usually starts with 1 and counts up to the maximum number of supported channels. The software however starts numbering with a 0 for the least significant bit in a word (LSB). The Quantum I/O modules have their lowest channel mapped to the most significant bit (MSB). The following figure shows the mapping of I/O channels related to the bits in a word:.
Word Addressing Versus Bit Addressing
Mainly discrete I/O modules can be configured to deliver their I/O data either in word format or in bit format. This can be selected during configuration by selecting either %IW (%MW) or %I (%M). If you need to access a single bit from an I/O module configured to use an I/O word, you can use the syntax %word.bit. The following table gives you the connection between I/O point number and the associated I/O address in bit and word addressing. The table shows a 32-point input module in the main rack, slot 4 configured with starting address %I1 or %IW1:
I/O channel Bit address (flat addressing) Bit address (topological addressing) Bit address extracted from word (flat addressing) Bit address extracted from word (topological addressing) 1 %I1 %I1.4.1[.0] %IW1.15 %IW1.4.1.1.15 2 %I2 %I1.4.2[.0] %IW1.14 %IW1.4.1.1.14 3 %I3 %I1.4.3[.0] %IW1.13 %IW1.4.1.1.13 • • • 15 %I15 %I1.4.15[.0] %IW1.1 %IW1.4.1.1.1 16 %I16 %I1.4.16[.0] %IW1.0 %IW1.4.1.1.0 17 %I17 %I1.4.17[.0] %IW2.15 %IW1.4.1.2.15 18 %I18 %I1.4.18[.0] %IW2.14 %IW1.4.1.2.14 • • • 31 %I31 %I1.4.31[.0] %IW2.1 %IW1.4.1.2.1 32 %I32 %I1.4.32[.0] %IW2.0 %IW1.4.1.2.0
Addressing Module Status Data
In addition to possible channel related diagnostics data, a module related status byte may be used. The status information of all modules in a Drop is administered by a table of %IW words. The starting address of this table can be entered in the configuration screen for the Drop. This information is not accessible through topological addressing. NOTE: The status information is only available if the module supports a status byte. For the meaning of the status byte check the module descriptions. Example of a Drop configuration screen with the starting address of the status table set to 100:
The following illustration shows how one word of the table conveys the status information for two modules:
Error Codes Table
Number of Blinks Code Error Slow (steady) 0000 Requested Kernal Mode 2 6820 hcb frame pattern error 6822 head cntrl blk diag error 6823 mod personality diag error 682A fatal start I/O error 682B bad read I/O pers request 682C bad execute diag request 6840 ASCII input xfer state 6841 ASCII output xfer state 6842 I/O input comm. state 6843 I/O output comm. state 6844 ASCII abort comm. state 6845 ASCII pause comm. state 6846 ASCII input comm. state 6847 ASCII output comm. state 6849 building 10 byte packet 684A building 12 byte packet 684B building 16 byte packet 684C illegal I/O drop number 3 6729 984 interface bus ack stuck high 4 6616 coax cable initialization error 6617 coax cable dma xfer error 6619 coax cable dumped data error 681A coax cable DRQ line hung 681C coax cable DRQ hung 5 6503 RAM address test error 6 6402 RAM data test error